Question GIGABYTE 5700 XT Bios mod fails

[AlleyCat]

Hi,
I am failing to update Gigabyte 5700 XT. The same procedure updates the BIOS on MSI cards with no problem. I follow the instructions on Igors Lab.

The sign of having trouble with the card bios flash shows in GPU-Z. After flash using amdvbflash the values of GPU and memory frequencies is empty. With stock bios there are Mhz frequencies.

Is there any known problems with flashing Gigabyte cards?
Any suggestions on what other forums I may ask for assistance?
Is it possible that the OEM bios is signed, and any modified bios will be rejected?
If the bios is signed, any tools to resign, or would I need to buy a card from a different vendor?

Thanks,

Alley Cat

 

[dapovoa]

Yes this is the default setting, the GFXOFF is to be disabled to prevent the 0 MH/s case.

What 0 MH/s case?

 

[Mini_Me]

What 0 MH/s case?

Some cards their gfx will go into deep sleep if a certain low power consumption is reached.

 

[Costis]

DS UCLK: Disable
GFXOFF: Enable
ACDC:

DS UCLK: ?
GFXOFF: ?
ACDC : ?
what is the correct setting?

 

[Mini_Me]

DS UCLK: ?
GFXOFF: ?
ACDC : ?
what is the correct setting?

Please only disable GFXOFF and leave the rest at default.

 

[dapovoa]

DS UCLK: ?
GFXOFF: ?
ACDC : ?
what is the correct setting?

DS UCLK: Disable (default)
GFXOFF: Disable
ACDC: Enable (default)

 

[Mini_Me]

Greetings,

Please test the vbios file kindly attached below for your Asus Dual Evo RX 5700,

 

[AnT]

Hi, thank you for rx5700xt guide (page 2) it save my card and my nerve. But now I have question, do I need to use OverdriveNtool after I flashed gpu to setup mem and core Clock and voltage?
GPU is gigabyte rx5700xt gaming OC rev.2 flashed with your recommended rev.2 bios (068), with Apple straps.

 

[Mini_Me]

Hi, thank you for rx5700xt guide (page 2) it save my card and my nerve. But now I have question, do I need to use OverdriveNtool after I flashed gpu to setup mem and core Clock and voltage?
GPU is gigabyte rx5700xt gaming OC rev.2 flashed with your recommended rev.2 bios (068), with Apple straps.

No need at all, by the way please check the guide again as I recently updated it.

 

[dapovoa]

Greetings,

Please test the vbios file kindly attached below for your Asus Dual Evo RX 5700,

Sorry, I don't see any difference...

 

[AnT]

No need at all, by the way please check the guide again as I recently updated it.

Thank you for quick response, I see that is changed Memory DPM3: 900 MHz, before was 910 MHz. I was asking for overdriveNtool, because I'am useing miner in windows.

 

[Mini_Me]

Sorry, I don't see any difference...

Can you set the memory clock at 900 or 910 MHz now?

 

[dapovoa]

Can you set the memory clock at 900 or 910 MHz now?

I could already done that. The problem was that all 3 risers were juiced with one single cable. So the outcome was good, only on trash cable (melted). Could be worse, I guess... so, I divided the output between two cables, now it's fine!
I programed the new bios, let me see if I wont get rejected shares untill tomorrow.

 

[dapovoa]

@Mini_Me What is Memory DPM 3, is this the base setting for high frequency?

 

[dapovoa]

Thank you for quick response, I see that is changed Memory DPM3: 900 MHz, before was 910 MHz. I was asking for overdriveNtool, because I'am useing miner in windows.

What mining software you're using?

 

[AnT]

Phoenix 5.4c, I didn't try trm, trm I have on rx580 rig. This is my first 5700xt.

What mining software you're using?

 

[Mini_Me]

@Mini_Me What is Memory DPM 3, is this the base setting for high frequency?

No, it is just to set the power curve for the memory, there is 5 DPM the last one number 5 is the maximum memory clock.

 

[dapovoa]

Phoenix 5.4c, I didn't try trm, trm I have on rx580 rig. This is my first 5700xt.

Ok, so you could do something with phoenixminer:
-cclock 1390 -cvddc 790 -mclock 915 -mvddc 1350 -tt -70

 

[dapovoa]

No, it is just to set the power curve for the memory, there is 5 DPM the last one number 5 is the maximum memory clock.

I only see four. 0, 1, 2, 3
And the 3 position (four) was 915 and now you've change to 900. So that why I asked.

 

[dapovoa]

I maintain the same settings as before:
C1390 / CV790 / VDDCI850 / M910 / MVDD 1350 ~56mh

The third card, the "not so good", only gives ~55mh

 

[dapovoa]

I programed the new bios, let me see if I wont get rejected shares untill tomorrow.